Location estimate

Belkhed

Maharashtra · India

Approximate location reference—not a rooftop, property or survey point.

Seasonal average-day estimates

Selected capacity 1 kWp

Showing the original estimates at 1 kWp. JavaScript is needed only to change capacity; source values and panel settings remain available below.

Changing capacity rescales my existing estimates. It does not recalculate their orientation, shading, equipment or loss assumptions.

Estimated average daily electricity for 1 kWp, in kWh/day, averaged over each season.

Summer

4.91

kWh/day

Autumn

4.91

kWh/day

Winter

4.75

kWh/day

Spring

6.68

kWh/day

Shared scale: 0–7.00 kWh/day.

I apply the same capacity factor to every season, so their proportions stay unchanged. The shared visual scale adjusts with capacity. To compare different system sizes, use the displayed kWh/day values.

This is illustrative scaling, not a site-specific production prediction.

Source basis and scaling limits

Original seasonal average-day estimates for Belkhed, in kWh/kWp/day.

I calculate the scaled results from the original seasonal values and round the final energy results to two decimal places. Exceptionally large values may appear in approximate scientific notation; the full results, rounded to two decimal places, remain available here.

Original source values and selected-capacity calculation
SeasonRecorded kWh/kWp/dayExact selected-capacity result · kWh/day
Summer 4.91 4.91 × 1 kWp = 4.91 kWh/day
Autumn 4.91 4.91 × 1 kWp = 4.91 kWh/day
Winter 4.75 4.75 × 1 kWp = 4.75 kWh/day
Spring 6.68 6.68 × 1 kWp = 6.68 kWh/day

Ordinary calculations wrap onto two lines. Exceptionally long calculations can be scrolled within their labelled region.

Full results rounded to two decimal places

These preserve every whole-number digit. Exceptionally long values can be scrolled horizontally inside each labelled result.

Summer · kWh/day
4.91
Autumn · kWh/day
4.91
Winter · kWh/day
4.75
Spring · kWh/day
6.68

The original values remain available without JavaScript. Energy always uses kWh/day, including when capacity is entered in MWp. Changing units preserves the same physical capacity.

These are seasonal average-day estimates, not annual totals or installation sizing. Changing capacity does not revisit the assumptions used in my original estimates.

Detailed site analysisExplore historical generation and system configurations for your own project or your clients in the profileSOLAR app.

Year-round panel setup

Schematic catalogue setting — Year-round fixed panel setup: tilt 20 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Year-round fixed panel setup · schematic
Tilt from horizontal
20°
Facing direction
South

Catalogue direction; exact azimuth not recorded. The facing direction is illustrative.

Suggested seasonal tilts

Tilt from horizontal · facing direction

Summer
Jun, Jul, Aug
4°South
Autumn
Sep, Oct, Nov
27°South
Winter
Dec, Jan, Feb
36°South
Spring
Mar, Apr, May
14°South

The seasonal electricity figures do not model gains from switching between these settings.

About this orientation

This schematic shows the year-round panel tilt and facing direction for Belkhed, Maharashtra, India.

For the year-round panel tilt, I used a simplified solar-noon calculation. This gives a broad starting point for considering a fixed panel angle at the location.

I weighted the daily angles by their share of estimated output. Read how I calculated panel tilt.

The panel shows tilt above horizontal on a fixed compass. North stays at the upper right in this projected view. Schematic only—not roof geometry, an installation drawing or a selected practical design.

Year-round and seasonal panel angles are separate estimates. Changing capacity rescales the existing energy values; it does not recalculate output for a different angle or facing direction.

Seasonal orientation diagrams

These show the separate seasonal settings above. Changing capacity does not change these angles or recalculate energy for a different orientation.

Summer

Schematic catalogue setting — Summer panel setup: tilt 4 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Summer panel setup · schematic

4° tilt · South

Illustrative direction; exact azimuth not recorded.

Autumn

Schematic catalogue setting — Autumn panel setup: tilt 27 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Autumn panel setup · schematic

27° tilt · South

Illustrative direction; exact azimuth not recorded.

Winter

Schematic catalogue setting — Winter panel setup: tilt 36 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Winter panel setup · schematic

36° tilt · South

Illustrative direction; exact azimuth not recorded.

Spring

Schematic catalogue setting — Spring panel setup: tilt 14 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Spring panel setup · schematic

14° tilt · South

Illustrative direction; exact azimuth not recorded.

Historical hourly-by-season solar output chart for Belkhed, India. View larger
Original chart units: hourly average electricity output in kWh per kW of installed solar PV.

Hourly electricity pattern for Belkhed, India

Hourly profiles by season — Belkhed, India · 2021

This chart shows how average electricity output varies through the hours of the day in each season. I have kept its original per-capacity basis: changing the capacity slider does not change this chart.

2021 is the method’s reference year, not verified year coverage for every point in this historical chart.

The cards above show seasonal average-day energy; this chart shows the hourly pattern. View the year-round panel setup.

Historical hourly chart

Hourly profiles by season — Belkhed, India · 2021

Swipe to pan, or focus the chart and use arrow keys.

Original chart units: hourly average electricity output in kWh per kW of installed solar PV.

This chart shows how average electricity output varies through the hours of the day in each season. I have kept its original per-capacity basis: changing the capacity slider does not change this chart.

The cards above show seasonal average-day energy; this chart shows the hourly pattern.

2021 is the method’s reference year, not verified year coverage for every plotted point.

Enlargement is limited to the original image resolution.

Row-spacing planning

Planning solar-panel row spacing in Belkhed

Explore the space between parallel panel rows at one assumed winter-solstice solar-noon position.

Example: 2 m panel surface length, recorded year-round tilt and no added margin. Enable JavaScript to change these inputs.

Row pitch including margin

≈ 2.54 m

Proportional side viewDesign sun: ≈ 45.89° above horizontal
Row 1 Row 2 Clear gap Added margin: 0 m Row pitch including margin
  • Sunlight ray
  • First row’s ground shadow
  • Shadow endpoint
Calculated clear gap
≈ 0.66 m
Added margin
≈ 0 m
Gap including margin
≈ 0.66 m
Panel horizontal footprint
≈ 1.88 m
Panel vertical rise
≈ 0.68 m
Pitch before margin
≈ 2.54 m

Simplified level ground, equator-facing cross-section. Approximate Northern Hemisphere winter solstice at solar noon (day 355). The separate recorded facing direction is not an input.

One sun position, not a complete site-shading assessment. A geometric zero gap does not establish adequate installation, access or maintenance clearance.

Detailed inputs and unrounded results

More digits retain calculation precision; they do not imply greater model accuracy. Pitch including margin is pitch before margin plus the added margin, including when that margin is zero.

Panel surface length
2 m
Tilt up from horizontal
20°
Added margin
0 m
Latitude from the catalogue
20.655300000000000000° (Northern Hemisphere)
Panel horizontal footprint
1.8793852415718169 m
Panel vertical rise
0.6840402866513374 m
Calculated clear gap
0.662998833594028 m
Pitch before margin
2.542384075165845 m
Gap including margin
0.662998833594028 m
Row pitch including margin
2.542384075165845 m
Design solar elevation
45.89491715318635°
How this spacing estimate is calculated

I calculate this example at approximate winter solstice and solar noon for the location’s hemisphere. Tilt is measured up from horizontal and panel length is measured along the tilted module surface.

δ = 23.45° × sin(360° × (day − 81) ÷ 365); α = asin(sin(latitude) × sin(δ) + cos(latitude) × cos(δ)).

Rise = length × sin(tilt). Footprint = length × cos(tilt). Clear gap = rise ÷ tan(α). Row pitch = footprint + clear gap. The optional margin is added to the gap and pitch.

The calculated clear gap is the horizontal distance from the first panel’s high edge to its shadow endpoint. Any added margin then extends to the next row. Pitch is measured between corresponding leading edges, not just across the clear gap. The target is no geometric shadow at that one simplified solar-noon design instant.

The cross-section assumes parallel, equator-facing rows and a solar-noon ray perpendicular to them. The method ignores azimuth error and does not use the separate facing direction recorded for this location.

Terrain, mounting height, module thickness, obstructions, structural loads and regulations are outside this simplified geometry. A qualified designer should verify a real installation.

Detailed site analysisExplore historical generation and system configurations for your own project or your clients in the profileSOLAR app.

Solar context for Belkhed

Read this location context alongside the calculation method and limitations; installation guidance is not a site-specific assessment.

<h3>Solar Energy Potential in Belkhed, India</h3>

Read the full article

Belkhed, India, located at 20.6553° N, 77.5451° E, offers promising conditions for solar photovoltaic (PV) energy generation throughout the year. This tropical location benefits from consistent sunlight patterns with seasonal variations primarily characterized by wet and dry periods rather than extreme temperature fluctuations. The solar energy production potential in Belkhed shows interesting seasonal patterns. During summer and autumn, the location yields identical outputs of 4.91 kWh per day for each kilowatt of installed solar capacity. Winter sees a slight decrease to 4.75 kWh/day per kW installed, representing only a minor reduction in estimated daily electricity output. Most notably, spring emerges as the standout season with an impressive 6.68 kWh/day per kW installed, significantly higher than other times of the year. <h3>Optimal Panel Installation</h3> For maximizing year-round solar energy production in Belkhed, fixed solar panels should be installed at a tilt angle of 20 degrees facing South. This specific angle has been calculated to optimize solar capture throughout the year, accounting for the Earth's elliptical orbit and the location's position in the Northern Hemisphere. <h3>Environmental and Weather Considerations</h3> Several environmental factors could potentially impact solar production efficiency in Belkhed: <ul> <li>Monsoon season brings heavy rainfall, typically between June and September, which can temporarily reduce solar output due to cloud cover and precipitation.</li> <li>Dust accumulation is a significant concern in this semi-arid region, as it can reduce panel efficiency by up to 25% if left unaddressed.</li> <li>Occasional high temperatures during peak summer months may slightly decrease panel efficiency.</li> </ul> <h3>Recommended Preventative Measures</h3> To mitigate these environmental challenges and maximize solar energy production in Belkhed, consider implementing these preventative measures: <ul> <li>Install an automated cleaning system or implement a regular manual cleaning schedule to remove dust buildup, especially during the dry season.</li> <li>Use solar panels with a lower temperature coefficient to minimize efficiency losses during hot weather.</li> <li>Consider slightly increasing the tilt angle of panels during monsoon season to facilitate natural cleaning from rainfall.</li> <li>Install lightning protection systems and proper grounding to protect the installation during seasonal thunderstorms.</li> <li>Select high-quality inverters with good performance in high-temperature conditions.</li> </ul> With these considerations addressed, Belkhed presents an excellent location for solar PV deployment, with spring offering exceptional generation potential and relatively consistent output during the rest of the year.

Topography around Belkhed

These landscape descriptions provide general context. The calculations do not model terrain, obstructions, shading or property suitability.

The topography around Belkhed, India, situated at coordinates 20.6553°N, 77.5451°E, is characterized by gently rolling terrain with moderate undulations typical of the Deccan Plateau region. This area in Maharashtra's Buldhana district features a mix of flat plains interspersed with shallow valleys and occasional low hills. The elevation generally ranges between 300-400 meters above sea level, creating a landscape that gradually slopes in various directions with natural drainage patterns feeding into local water systems.

Read the full topography description

<h3>Terrain Features</h3> The immediate vicinity of Belkhed presents predominantly agricultural lands with scattered settlements. The terrain consists of weathered basaltic rock formations underneath fertile black cotton soil, characteristic of this part of central India. Small seasonal streams crisscross the landscape, typically flowing during the monsoon season and remaining dry for the remainder of the year. The region experiences moderate relief with gradual elevation changes rather than steep slopes, making much of the land accessible and usable for various purposes. <h3>Optimal Areas for Solar PV Development</h3> For large-scale solar photovoltaic installations, the most suitable areas near Belkhed would be the relatively flat, open plains located primarily to the east and southeast of the settlement. These areas combine several favorable characteristics for solar development: The gently sloping terrain with southern exposure maximizes solar radiation capture throughout the day. These locations typically have minimal shadowing effects from topographical features, ensuring consistent energy production. Additionally, these areas often feature less productive agricultural land with sparse vegetation, minimizing the environmental impact of conversion to solar use. The northwestern sectors near Belkhed, while still viable, present slightly more varied topography with occasional low ridges that might create partial shadowing during certain times of day. Areas with southern aspects (south-facing slopes) throughout the region would generally be preferable for maximizing solar gain throughout the year. <h3>Topographical Considerations for Development</h3> When evaluating specific sites for solar development, several topographical factors merit consideration. The black cotton soil prevalent in the region exhibits significant shrink-swell properties, which can affect foundation stability for solar installations. Proper engineering solutions would be necessary to address this characteristic. Areas near seasonal water channels should be avoided due to potential flooding risks during monsoon seasons. While these channels remain dry most of the year, they can experience rapid water flow during heavy rainfall events. The gentle slopes in the region generally provide good natural drainage, which is beneficial for preventing water accumulation around solar infrastructure. The moderate relief of the landscape would require minimal grading for large installations, reducing site preparation costs compared to more rugged terrains. The open nature of the landscape also means fewer natural obstacles that would otherwise need clearing, further enhancing the economic viability of solar development in this region.

Technical location reference

Approximate map point used for Belkhed, India

This coordinate is the calculation reference for Belkhed, India. Extra decimal places do not make it a rooftop, property or survey point.

Coordinates and precision
Map coordinate
20.655300000000000000, 77.545100000000000000
Originally displayed coordinate
lat20.6553 / long77.5451

How the estimate works

How this Belkhed estimate was calculated

Here is how I calculated the location estimate for Belkhed, India.

Read how all Location estimates work

Source and scope

I calculated these location estimates using hourly NASA POWER solar-resource data, with 2021 as the reference year. The seasonal figures show estimated daily electricity production averaged over each season, on a common panel-capacity basis.

The figures are calculated estimates, not measured output or a new NASA request while you browse.

Reference period and source details

The reference year describes the intended input period; complete source-year coverage is not established for every historical result. Read the technical questions about source data and downloads.

NASA POWER project reference

The data was obtained from National Aeronautics and Space Administration (NASA) Langley Research Center's Prediction Of Worldwide Energy Resources (POWER) project funded through the NASA Earth Science Division.

This source reference does not imply NASA endorsement.

Use the result carefully

What this Belkhed Location estimate includes and leaves out

Use the Belkhed figures for broad location context, with the following boundaries in mind.

  • These catalogue estimates are informational; they do not establish a site-specific production result.
  • The location is an approximate reference, not a property, rooftop or survey coordinate.
  • The energy figures support broad location comparisons; they are not a generation guarantee or detailed system design.
  • The seasonal cards show average-day energy. An hourly chart, where available, shows a different view of the daily pattern.
  • Distance and clearance between rows require panel dimensions, mounting height, terrain, acceptable shading and a project-specific design.

Keep exploring

Compare Belkhed with another location

Back to country results

Detailed site analysis

Take it a step further

Whether you’re exploring solar for your own project or comparing options for your clients, profileSOLAR helps you assess historical generation, compare system configurations and produce clear reports.

Detailed analysis for your project or your clients.

Explore features and paid access in the app, or use the complimentary testing access included in your invitation.

Analysis features and access

The profileSOLAR app supports hourly solar analysis over periods of up to five consecutive years, subject to available source data. No electricity-use file is required for this solar analysis.

Compare supported panel configurations, then download Summary or Detailed PDF reports for the saved Analysis.

Testing access includes only the features and allowances stated in your invitation. Your catalogue selection is not transferred; choose your exact site in the app.

Explore detailed site analysis