Location estimate

Hyderabad

Sindh · Pakistan

Approximate location reference—not a rooftop, property or survey point.

Seasonal average-day estimates

Selected capacity 1 kWp

Showing the original estimates at 1 kWp. JavaScript is needed only to change capacity; source values and panel settings remain available below.

Changing capacity rescales my existing estimates. It does not recalculate their orientation, shading, equipment or loss assumptions.

Estimated average daily electricity for 1 kWp, in kWh/day, averaged over each season.

Summer

6.61

kWh/day

Autumn

5.46

kWh/day

Winter

4.86

kWh/day

Spring

7.21

kWh/day

Shared scale: 0–8.00 kWh/day.

I apply the same capacity factor to every season, so their proportions stay unchanged. The shared visual scale adjusts with capacity. To compare different system sizes, use the displayed kWh/day values.

This is illustrative scaling, not a site-specific production prediction.

Source basis and scaling limits

Original seasonal average-day estimates for Hyderabad, in kWh/kWp/day.

I calculate the scaled results from the original seasonal values and round the final energy results to two decimal places. Exceptionally large values may appear in approximate scientific notation; the full results, rounded to two decimal places, remain available here.

Original source values and selected-capacity calculation
SeasonRecorded kWh/kWp/dayExact selected-capacity result · kWh/day
Summer 6.61 6.61 × 1 kWp = 6.61 kWh/day
Autumn 5.46 5.46 × 1 kWp = 5.46 kWh/day
Winter 4.86 4.86 × 1 kWp = 4.86 kWh/day
Spring 7.21 7.21 × 1 kWp = 7.21 kWh/day

Ordinary calculations wrap onto two lines. Exceptionally long calculations can be scrolled within their labelled region.

Full results rounded to two decimal places

These preserve every whole-number digit. Exceptionally long values can be scrolled horizontally inside each labelled result.

Summer · kWh/day
6.61
Autumn · kWh/day
5.46
Winter · kWh/day
4.86
Spring · kWh/day
7.21

The original values remain available without JavaScript. Energy always uses kWh/day, including when capacity is entered in MWp. Changing units preserves the same physical capacity.

These are seasonal average-day estimates, not annual totals or installation sizing. Changing capacity does not revisit the assumptions used in my original estimates.

Detailed site analysisExplore historical generation and system configurations for your own project or your clients in the profileSOLAR app.

Year-round panel setup

Schematic catalogue setting — Year-round fixed panel setup: tilt 23 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Year-round fixed panel setup · schematic
Tilt from horizontal
23°
Facing direction
South

Catalogue direction; exact azimuth not recorded. The facing direction is illustrative.

Suggested seasonal tilts

Tilt from horizontal · facing direction

Summer
Jun, Jul, Aug
9°South
Autumn
Sep, Oct, Nov
31°South
Winter
Dec, Jan, Feb
40°South
Spring
Mar, Apr, May
19°South

The seasonal electricity figures do not model gains from switching between these settings.

About this orientation

This schematic shows the year-round panel tilt and facing direction for Hyderabad, Sindh, Pakistan.

For the year-round panel tilt, I used a simplified solar-noon calculation. This gives a broad starting point for considering a fixed panel angle at the location.

I weighted the daily angles by their share of estimated output. Read how I calculated panel tilt.

The panel shows tilt above horizontal on a fixed compass. North stays at the upper right in this projected view. Schematic only—not roof geometry, an installation drawing or a selected practical design.

Year-round and seasonal panel angles are separate estimates. Changing capacity rescales the existing energy values; it does not recalculate output for a different angle or facing direction.

Seasonal orientation diagrams

These show the separate seasonal settings above. Changing capacity does not change these angles or recalculate energy for a different orientation.

Summer

Schematic catalogue setting — Summer panel setup: tilt 9 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Summer panel setup · schematic

9° tilt · South

Illustrative direction; exact azimuth not recorded.

Autumn

Schematic catalogue setting — Autumn panel setup: tilt 31 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Autumn panel setup · schematic

31° tilt · South

Illustrative direction; exact azimuth not recorded.

Winter

Schematic catalogue setting — Winter panel setup: tilt 40 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Winter panel setup · schematic

40° tilt · South

Illustrative direction; exact azimuth not recorded.

Spring

Schematic catalogue setting — Spring panel setup: tilt 19 degrees above horizontal; facing South. Direction is illustrative; exact azimuth not recorded.NESW
Spring panel setup · schematic

19° tilt · South

Illustrative direction; exact azimuth not recorded.

Historical hourly-by-season solar output chart for Hyderabad, Pakistan. View larger
Original chart units: hourly average electricity output in kWh per kW of installed solar PV.

Hourly electricity pattern for Hyderabad, Pakistan

Hourly profiles by season — Hyderabad, Pakistan · 2021

This chart shows how average electricity output varies through the hours of the day in each season. I have kept its original per-capacity basis: changing the capacity slider does not change this chart.

2021 is the method’s reference year, not verified year coverage for every point in this historical chart.

The cards above show seasonal average-day energy; this chart shows the hourly pattern. View the year-round panel setup.

Historical hourly chart

Hourly profiles by season — Hyderabad, Pakistan · 2021

Swipe to pan, or focus the chart and use arrow keys.

Original chart units: hourly average electricity output in kWh per kW of installed solar PV.

This chart shows how average electricity output varies through the hours of the day in each season. I have kept its original per-capacity basis: changing the capacity slider does not change this chart.

The cards above show seasonal average-day energy; this chart shows the hourly pattern.

2021 is the method’s reference year, not verified year coverage for every plotted point.

Enlargement is limited to the original image resolution.

Row-spacing planning

Planning solar-panel row spacing in Hyderabad

Explore the space between parallel panel rows at one assumed winter-solstice solar-noon position.

Example: 2 m panel surface length, recorded year-round tilt and no added margin. Enable JavaScript to change these inputs.

Row pitch including margin

≈ 2.73 m

Proportional side viewDesign sun: ≈ 41.2° above horizontal
Row 1 Row 2 Clear gap Added margin: 0 m Row pitch including margin
  • Sunlight ray
  • First row’s ground shadow
  • Shadow endpoint
Calculated clear gap
≈ 0.89 m
Added margin
≈ 0 m
Gap including margin
≈ 0.89 m
Panel horizontal footprint
≈ 1.84 m
Panel vertical rise
≈ 0.78 m
Pitch before margin
≈ 2.73 m

Simplified level ground, equator-facing cross-section. Approximate Northern Hemisphere winter solstice at solar noon (day 355). The separate recorded facing direction is not an input.

One sun position, not a complete site-shading assessment. A geometric zero gap does not establish adequate installation, access or maintenance clearance.

Detailed inputs and unrounded results

More digits retain calculation precision; they do not imply greater model accuracy. Pitch including margin is pitch before margin plus the added margin, including when that margin is zero.

Panel surface length
2 m
Tilt up from horizontal
23°
Added margin
0 m
Latitude from the catalogue
25.350700000000000000° (Northern Hemisphere)
Panel horizontal footprint
1.8410097069048807 m
Panel vertical rise
0.7814622569785474 m
Calculated clear gap
0.8926723237698977 m
Pitch before margin
2.733682030674778 m
Gap including margin
0.8926723237698977 m
Row pitch including margin
2.733682030674778 m
Design solar elevation
41.199517153186356°
How this spacing estimate is calculated

I calculate this example at approximate winter solstice and solar noon for the location’s hemisphere. Tilt is measured up from horizontal and panel length is measured along the tilted module surface.

δ = 23.45° × sin(360° × (day − 81) ÷ 365); α = asin(sin(latitude) × sin(δ) + cos(latitude) × cos(δ)).

Rise = length × sin(tilt). Footprint = length × cos(tilt). Clear gap = rise ÷ tan(α). Row pitch = footprint + clear gap. The optional margin is added to the gap and pitch.

The calculated clear gap is the horizontal distance from the first panel’s high edge to its shadow endpoint. Any added margin then extends to the next row. Pitch is measured between corresponding leading edges, not just across the clear gap. The target is no geometric shadow at that one simplified solar-noon design instant.

The cross-section assumes parallel, equator-facing rows and a solar-noon ray perpendicular to them. The method ignores azimuth error and does not use the separate facing direction recorded for this location.

Terrain, mounting height, module thickness, obstructions, structural loads and regulations are outside this simplified geometry. A qualified designer should verify a real installation.

Detailed site analysisExplore historical generation and system configurations for your own project or your clients in the profileSOLAR app.

Solar context for Hyderabad

Read this location context alongside the calculation method and limitations; installation guidance is not a site-specific assessment.

Hyderabad's solar reference is strongest in spring. Estimated average daily electricity for each 1 kW of rated panel capacity is 7.21 kWh/day in spring, 6.61 kWh/day in summer, 5.46 kWh/day in autumn and 4.86 kWh/day in winter. The figures support a useful comparison across seasons without describing generation as constant throughout the year.

Read the full article

The city belongs to Sindh's lower Indus landscape, but its terrain is not uniformly flat. The Ganjo Takkar limestone ridge extends south from Hyderabad through the broader alluvial setting. This ridge-and-plain contrast is a distinctive part of the locality and more informative than treating every open-looking surface as desert land. The recorded year-round fixed-panel reference is 23° from horizontal, facing South. Our output-weighted method uses simplified solar geometry. A receiving roof's actual plane, support and nearer skyline need to be examined alongside that broad setting. Sunlight and module temperature have different effects: hotter cells generally produce less power at the same irradiance. Ventilation can be a design consideration, but it cannot remove the temperature response or compensate for sunlight absent under cloud. Likewise, cleaning addresses deposits on the receiving surface rather than atmospheric haze. Around the Indus plain, cultivated land, channels and changes of level are existing landscape features. Neither a sparse surface nor proximity to a power line establishes that land is unused or a connection is available. Actual receiving levels and water routes matter even where the regional gradient appears slight. Hyderabad's figures are best read beside a defined electricity demand and usable receiving area. The limestone ridge, built city and alluvial surroundings give that comparison a local frame, while project costs and conditions remain questions for the particular surface being assessed.

Topography around Hyderabad

These landscape descriptions provide general context. The calculations do not model terrain, obstructions, shading or property suitability.

Hyderabad sits within the broader lower Indus alluvial landscape. Ganjo Takkar is a limestone ridge extending southward from the city, interrupting the plain rather than forming part of a uniformly level setting.

Read the full topography description

The surrounding plain contains cultivated ground, water routes and lower depressions. River-deposited material and exposed limestone are different physical settings, but neither establishes foundation performance at an individual plot. Conditions need to be investigated at the actual receiving site. The ridge also adds a local horizon that is separate from nearby buildings and trees. Its apparent height depends on distance and direction; a low nearby obstruction may cover more of the solar path than higher terrain farther away. Calling ground barren or semi-arid does not establish that it has no existing use. The ridge–plain–river relationship is useful descriptive context for Hyderabad without selecting supposed vacant land or calculating property-level shadows, support or water exposure.

Technical location reference

Approximate map point used for Hyderabad, Pakistan

This coordinate is the calculation reference for Hyderabad, Pakistan. Extra decimal places do not make it a rooftop, property or survey point.

Coordinates and precision
Map coordinate
25.350700000000000000, 68.353400000000000000
Originally displayed coordinate
lat25.3507 / long68.3534

How the estimate works

How this Hyderabad estimate was calculated

Here is how I calculated the location estimate for Hyderabad, Pakistan.

Read how all Location estimates work

Source and scope

I calculated these location estimates using hourly NASA POWER solar-resource data, with 2021 as the reference year. The seasonal figures show estimated daily electricity production averaged over each season, on a common panel-capacity basis.

The figures are calculated estimates, not measured output or a new NASA request while you browse.

Reference period and source details

The reference year describes the intended input period; complete source-year coverage is not established for every historical result. Read the technical questions about source data and downloads.

NASA POWER project reference

The data was obtained from National Aeronautics and Space Administration (NASA) Langley Research Center's Prediction Of Worldwide Energy Resources (POWER) project funded through the NASA Earth Science Division.

This source reference does not imply NASA endorsement.

Use the result carefully

What this Hyderabad Location estimate includes and leaves out

Use the Hyderabad figures for broad location context, with the following boundaries in mind.

  • These catalogue estimates are informational; they do not establish a site-specific production result.
  • The location is an approximate reference, not a property, rooftop or survey coordinate.
  • The energy figures support broad location comparisons; they are not a generation guarantee or detailed system design.
  • The seasonal cards show average-day energy. An hourly chart, where available, shows a different view of the daily pattern.
  • Distance and clearance between rows require panel dimensions, mounting height, terrain, acceptable shading and a project-specific design.

Keep exploring

Compare Hyderabad with another location

Back to country results

Detailed site analysis

Take it a step further

Whether you’re exploring solar for your own project or comparing options for your clients, profileSOLAR helps you assess historical generation, compare system configurations and produce clear reports.

Detailed analysis for your project or your clients.

Explore features and paid access in the app, or use the complimentary testing access included in your invitation.

Analysis features and access

The profileSOLAR app supports hourly solar analysis over periods of up to five consecutive years, subject to available source data. No electricity-use file is required for this solar analysis.

Compare supported panel configurations, then download Summary or Detailed PDF reports for the saved Analysis.

Testing access includes only the features and allowances stated in your invitation. Your catalogue selection is not transferred; choose your exact site in the app.

Explore detailed site analysis